( Krypton Interrupter zener heatsink - zener slots
( Set start reference datum at x-1000, y5000
( Install 9 mm ball nosed drill
( Spindle speed set to 2000~2500rpm
( operation begins automatically when quil TDC switch is opened
( raise the quill at the end of the last X+zzzmm stroke
( with appropriate care the part can be remove the part during the parked condition
( 80% Kero+ 20% RTD used as cutting lubricant during the X+13100mm cutting stroke
( return speed may be increased if justified by higher production rate
clr		( clear all existing programs/commands
p		( begin programme
m 1		( set motor to FULL step mode
t 200		( set start speed to 200 steps/sec
max 400	    ( set MAXimum motor speed to steps per sec. i.e. 400 steps/sec
a 500		( set acceleration to 500 steps/sec/sec
de 500      ( set deceleration to 1500 steps/sec/sec
k 50        ( sets step constant to 50 ?
s 4 0          ( drill up
x 550          ( move "x" axis +5.50mm
y 400          ( move "y" axis 4.00mm
s 4 1       ( lower tool
o 1 1
w 40        ( delay 6 seconds for drill penetration
max 100	( set MAXimum motor speed to steps per sec
y 4200	  ( cut slot 1
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 100
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y -4200	  ( cut slot 2
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 100
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y 4200	  ( cut slot 3
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 200
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y -4200	  ( cut slot 4
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 100
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y 4200	  ( cut slot 5
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 100
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y -4200	  ( cut slot 6
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 100
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y 4200	  ( cut slot 7
o 1 0
s 4 0       ( raise tool
max 400
x 1000	( move across 10 mm
max 100
s 4 1       ( lower tool
o 1 1
w 40        ( delay 5 seconds for drill penetration
y -4200	  ( cut slot 8
o 1 0
s 4 0       ( raise tool
max 400	( set MAXimum motor speed to steps per sec. i.e. 400 steps/sec
x -7550	( return home
y -400
s 4 0           ( BDC switch OPEN - press is cycling or at TDC
s 4 1	          ( BDC switch CLOSED - identifies that drill is in the part
c 0             ( turn motor current off
g               ( go to begining and repeat as often as job/parts require