======================================================
License Agreement for Fuji Xerox PCL 6 Printer Driver
======================================================

1. PROPRIETARY RIGHTS: Title, ownership rights, and intellectual
   property rights in the SOFTWARE shall remain in Fuji Xerox and its
   third party suppliers.  You have no rights in the SOFTWARE except
   as expressly granted in accordance with this agreement.
   
2. LICENSE:  Under this agreement, you are granted a non-exclusive
   license to use the SOFTWARE for the purpose of using with
   compatible Fuji Xerox products in your country.  You are
   not permitted to (1) assign, sublicense, sell, rent, lease, convey,
   or transfer the SOFTWARE to any third party by any tangible media
   such as floppy disk, magnetic tape, or CD-ROM, (2) distribute the
   SOFTWARE on a network or by a telephone line available to the public or
   (3) alter, modify, decompile, disassemble, reverse engineer, or create
   derivative works based on the whole or any part of the SOFTWARE.
   If any direction on usage or restriction for the SOFTWARE is
   expressly specified in this web site, you are required to follow
   such direction. 
   
3. TERM: This agreement is effective upon installing the SOFTWARE
   until you terminate the agreement by destroying the SOFTWARE.
   This agreement will also terminate if you fail to abide by any
   terms of this agreement.  In case of termination, you must
   promptly destroy the SOFTWARE.
   
4. LIMITED WARRANTIES: THE SOFTWARE IS SUPPLIED STRICTLY ON AN 'AS IS'
   BASIS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR
   FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE SOFTWARE.
   YOU ARE RESPONSIBLE FOR CHOOSING, MAINTAINING AND MATCHING OTHER
   HARDWARE AND SOFTWARE COMPONENTS IN COMBINATION OF THE SOFTWARE.
   IN NO EVENT, SHALL FUJI XEROX, FUJI XEROX CHANNEL PARTNERS,
   AUTHORIZED DEALERS AND THEIR THIRD PARTY SUPPLIERS BE LIABLE FOR
   ANY LOSS OR DAMAGE INCLUDING INCIDENTAL OR CONSEQUENTIAL LOSS OR
   DAMAGE, ARISING FROM USE OF OR INABILITY TO USE SOFTWARE, OR ANY
   MODIFICATION OF THE SOFTWARE.  
   
5. EXPORT CONTROL: You are not allowed to export the SOFTWARE in part
   or whole, directly or indirectly, in violation of any restrictions,
   laws or regulations imposed by the government of your country or
   any other relevant countries, and are required to obtain necessary
   approval prior to exporting the SOFTWARE.


-----------------------------------------------------------------------------------
---   Fuji Xerox Document Centre 285/235 PCL 6 Version 1.1.9/1.1.9   ---
---               Printer Driver for Windows NT4.0/2000/XP                     ---
---                           March 2003                          		  ---
---                                                                  			  ---
---                              Readme                              		  ---
-----------------------------------------------------------------------------------

This document describes

  1. Installation file list.
  2.1 Installation of this driver.
  2.2 Installation under Windows NT(R)4.0/2000/XP (Setup.exe)
  2.3 Uninstallation. (Unsetup.exe)
  3.1 Installation under Windows NT(R) 4.0 (Add Printer Wizard)
  3.2 Installation under Windows(R)2000 (Add Printer Wizard)
  3.3 Installation under Windows(R) XP (Add Printer Wizard)
  3.4 Installing Using the Plug&Play Function (for Windows(R)2000/XP)
  3.5 Uninstallation. (Add Printer Wizard, Plug & Play)
  4.  Notes for Watermarks.
  5.  General Comments.
  6.  Limitations.
  7.  Known Problems.
  8.  Software Update.

1. Installation file list
=========================

FX6HAEK.DLL
FX6HAEU.DLL
FX6HAEP.DLL
FX6HAEC.DLL
FX6HAEL.DLL
FX6HAEX.DLL
FX6HAES.DLL
FX6HAEJ.DLL
FX6HAEQ.EXE
FX6HAEWU.DLL
FX6HAEWK.DLL
FX6HAEZU.DLL
FX6HAEZK.DLL
FX6HAEZ1.EXE
FX6HAE.HLP
FX6HAEZ.EXE
FX6HAEI3.DLL

FX6HBEK.DLL
FX6HBEU.DLL
FX6HBEP.DLL
FX6HBEC.DLL
FX6HBEL.DLL
FX6HBEX.DLL
FX6HBES.DLL
FX6HBEJ.DLL
FX6HBEQ.EXE
FX6HBEWU.DLL
FX6HBEWK.DLL
FX6HBEZU.DLL
FX6HBEZK.DLL
FX6HBEZ1.EXE
FX6HBE.HLP
FX6HBEZ.EXE
FX6HBEI3.DLL

SETUP.EXE
UNSETUP.EXE

FXXL28EH.INF (for Windows(R)2000/XP)
FXXL28EI.INF (for Windows(R)NT4.0)


2.1 Installation of this driver
===============================

Follow the instructions below to install PCL6 printer drivers.


**Note**
Driver installation by Windows Add Printer Wizard is permitted only for
users who obtain driver distribution files via the CD-ROM or floppy disk
from Fuji Xerox Co., Ltd..
If your driver distribution files are received via electronic mail or by
downloading from WWW, you should run the driver Setup.exe to install it.
During the SetUp operation, you have to agree and accept the End User
License Agreement in order to proceed for a successful driver installation.


Please replace <LANG> of the explanation of the directory in the 
text with the directory name of each language. 
In an English version, <LANG> replaces "English".

Here we will install and uninstall the Document Centre 285 PCL 6 printer
driver as an example.

2.2 Installation under Windows(R)NT4.0/2000/XP (Setup.exe)
=======================================================

(1) Start Windows NT4.0/2000/XP and insert the "PCL Driver/Network Utility" 
    CD-ROM in the CD-ROM drive.

(2) Open the folder which contains the installer program.
	"My Computer" > "FXOPS-PCL (E:)" > <LANG> > <Product>
	> <OS> > "PCL6" > "Setup"
  
   You can find the SETUP.EXE in this folder. Double click it to start
   the installer program. Note that the [Add Printer] icon in the
   [Printers] window in the [Control Panel] is not available for this
   printer driver.

(3) Read the End User License Agreement and turn on left the check box 
    [I accept the terms of the above License Agreement] if you accept the
    terms. Then click the [Next] button.

(4) Now, the only selectable printer model on the first dialog of 
    the installer is "FX Document Centre 285 PCL 6". 

(5) Select the port used for the printer.

(6) If you DON'T want to make this the default printer, check it off and 
   click the [Next] button.

(7) If you want another name for this printer, input the name 
    and click the [Next] button.
    Default printer name is "FX Document Centre 285 PCL 6"

(8) Click the [Finish] button on the [Ready to Start Copying] dialog box.

(9) When the copying of files is completed, the [INSTALLATION SUCCESSFUL]
    dialog box appears. Click the [Printer Properties] or [Document
    Defaults] to configure the printer driver, or [Exit to Windows] to finish
    installation.

(10) Restart Windows NT/2000/XP system to make use of the printer driver.



2.3. Uninstallation (Unsetup.exe)
=================================

(1) Execute "Unsetup.exe" in the same folder where you executed the 
    "Setup.exe" in the "PCL Driver/Network Utility" CD-ROM.

(2) Select printer model for "FX Document Centre 285 PCL 6" in the 
    "Printer Uninstall" dialogue.If you changed the printer name, it is shown
    in the printer model list. And click the [Next] button.

(4) Click the [Finish] button on the "Ready to Start Deleting" dialog.

(5) To ensure a completely clean system or to re-install the printer driver,
    You must restart Windows.



3.1 Installation under WindowsNT(R) 4.0 (Add Printer Wizard)
============================================================


(1) Start Windows NT(R)4.0 and insert the "PCL Driver/Network Utility" CD-ROM
    in the CD-ROM drive.

(2) Click the [Add Printer] icon in the [Printers] windows from the
    [Control Panel]

(3) Following the steps of [Add Printer Wizard], you can choose the printer
    port.
 
(4) After you select the port of the printer, you will see the selection of
    [Manufactures:] and [Printers:]. Click [Have Disk...] in the dialog.

(5) Enter a path to a location of the INF file you are installing.
    You can also indicate the INF file location by [Browse]. 
    Open the Drive into which you inserted the CD-ROM. Then, open
 
	<LANG> > <Product> > "NT40" > "PCL6" > "AddPrint" folder.

    Select the INF file in the folder and then click [OK].

(6) "FX Document Centre 285 PCL 6" appears in the [Printers:] in the dialog.
    Select the printer and click [Next].
 
(7) When you finished all the steps of the [Add Printer Wizard], printer icon 
    will be created in the [Printers] dialog.
    It is recommended that you print a test page after completion of the
    printer driver installation in order to check if the driver was installed
    properly.



3.2 Installation under Windows(R)2000 (Add Printer Wizard)
==========================================================

Follow the instructions below to enable printing under Windows(R)2000.

(1) Click [Start], select [Settings], and then click [Printers].

(2) Double-click the [Add Printer] icon in the "Printers" dialog, 
    and then follow the instructions on the dialogs.

(3) If the printer is directly attached to your computer or is connected to
    the Network using the LPR protocol, choose [Local Printer] ,then click 
    [Next>] and follow the instructions from (7). Otherwise, choose 
    [Network printer].

(4) Connect to the desired printer by:
         * Searching for it in the Active Directory, or 
         * Clicking [Next>] to locate the printer on the network, or 
           typing its name using the following format. 
           
           \\printserver_name\share_name

    Then follow the instructions from (7).
    If you are not familiar with the network, please consult the network 
    administrator.

(5) Select the printer port where the printer device is connected directly,
    click [Next>], and go to step (7).
    If the printer is connected to the Network using the LPR protocol,
    select [Standard TCP/IP Port] of the [Create a new port:] section,
    and then click [Next>]. The "Welcome to the Add Standard TCP/IP Printer
    Port Wizard" dialog will be displayed. Click [Next>].

(6) Enter the Printer Name or IP address in the [Printer Name or IP Address]
    edit box. If you don't know the Printer Name or IP address, please consult
    the network administrator.
    The "Completing the Add Standard TCP/IP Printer Port Wizard" dialog will
    be displayed. Click [Finish].

(7) Click [Have Disk....] in the "Add Printer Wizard" and select the 
    INF file.

(8) If the INF file is loaded correctly, the printer models are listed in
    the dialog box. Select the printer you use.

(9) You may change the printer name, set it as a default printer or a shared
    printer or print the test page as you like.

(10) Follow the instructions on the dialog to finish the driver installation.


3.3 Installation under Windows(R)XP (Add Printer Wizard)
==========================================================

 1) Click the "Start" button.  Point to "Printers and Faxes" and        
    then click"Add a printer".  

 2) In the "Add Printer Wizard", click "Next".

 3) Specify the printer connection.  When printer is directly connected  
    or when it is connected through network by using LPR protocol, then select
    "Local printer attached to this computer". 
    Confirm that the check box "Automatically detect and install my Plug and Play 
    printer" is set to OFF, and then click "Next" to proceed to Step (5). 
    When the printer is connected through network, select "A network printer, 
    or a printer attached to another computer" and then click "Next". 

 4) Specify the printer name.  Enter a printer name or URL directly or 
    select a printer to be connected from the list of shared printers. 
    After selection, proceed to Step (7).
    (Contact the network administrator if you have any queries.)

    <Caution> Printing by entering URL is available only in IPP-supported
    models.

 5) When the printer is connected directly, select the port connected to 
    this product and click "Next".  Proceed to Step (7).
    When connecting directly to the printer through network using LPR 
    protocol, select "Standard TCP/IP Port" from "Create a new port" and 
    click "Next".
    "Add Standard TCP/IP Printer Port Wizard" is activated. Click "Next(N)".

 6) Enter the IP address for the printer into "Printer Name or IP Address", 
    on the TCP/IP Printer Port Wizard and then click "Next".
    (Contact the network administrator if you do not know the IP address.)
    Click "Finish".

 7) Select a printer model.  Click "Have Disk" to display the "Install 
    from Disk" dialog box.

 8) Specify the folder containing this INF file and click "OK". 
    * When installing from a CD-ROM, enter e.g."E:\FXOPS-PCL\Win2K_XP".
      In this example, E drive is used as the CD-ROM drive. 
      If you are using another drive for CD-ROMs, specify accordingly.

 9) From the list of printers displayed, select the printer you are using 
    and click "Next".

 10) Change the printer name, if necessary.  The message asking whether to 
     use this printer as the default printer is shown.  Make a selection and 
     then click "Next". 

 11) Specify whether to print the test page after installation.  If you 
     want to print, select "Yes".  If not, select "No".  Click "Finish".

 12) Follow the instruction on the screen to continue the installation.

 13) After the necessary files are copied, the installation is completed.  
     Confirm in the "Printers and Faxes" folder that the printer is added.



3.4 Installing Using the Plug&Play Function (for Windows(R)2000/XP)
=====================================================================

 Note that installation using the Plug&Play function is allowed
 only if the printer is connected to the PC using a bi-directional
 parallel cable

(1) Connect the PC and printer using an interface cable with the
    power supply to the PC and the printer switched off.  Then, turn
    on the power supply of the printer and the PC and start
    Windows2000/XP.

(2) The printer is detected and a "Found New Hardware Wizard" dialog
    box is displayed.  Select "Search for a suitable driver for my
    device (recommended)" on Windows 2000 and "Install the software
    automatically (recommended)" on Windows XP, and follow the screen 
    instructions.

(3) On Windows 2000, specify the location of the driver files 
    in "Locate Driver Files"and click the "Next" button. 
    When "Specify a location" is selected, enter the drive name
    (e.g.->E:) and the path name(\<Lang>\<Product>Win2K_XP\\PCL6\AddPrint)
    of the driver in the "Copy manufacturer's files from" input field
    on the screen and click the "OK" button.
    On Windows XP, specify the location of the driver files 
    in "Include this location in the search" in "Search for the best
    driver in these locations".  Enter the drive name(e.g.->E:) 
    and the path name(\<Lang>\<Product>Win2K_XP\\PCL6\AddPrint) 
    and click the "Next" button.

(4) On Windows 2000, a message is displayed to notify that device files 
    have been found, and click the "Next" button. A "Digital Signature 
    Not Found" dialog on Windows 2000 or a "Printers has not passed Windows
    Logo testing..." on Windows XP is displayed. Click "Yes" on Windows 
    2000 or "Continue Anyway" on Windows XP to continue installation.

(5) The required files are copied and a message is displayed to notify
    that installation is completed.  Click the "Finish" button.



3.5 Uninstallation. (Add Printer Wizard, Plug & Play)
=====================================================

(1) Delete the printer icon you installed in the [Printers] dialog from the 
    [Control Panel].



4. Notes for Watermarks
=======================

  The driver provides a wide input range in defining a watermark size,
  length & position. Such flexible user input enables a watermark to be
  created as small as to print on a Postcard or as large as to print on
  an A3 paper. However, an extremely large watermark may not be printed
  successfully on a relatively small paper in size.
  It is the user's responsibility to define an appropriate watermark for
  printing it on the selected paper type.

  The Watermark Preview is close to the printed result but it may not
  exactly match.
  A watermark may not be printed correctly for these cases:

(1) Depending on the selected (bolded) font type, a watermark with long
    text length and/or huge text size may hit the maximum working memory
    limit. As a result, the actual output may differ from the desired
    output.

(2) Due to the technical limitation of Raster printing mode, a watermark 
    cannot be printed in background of a document.

(3) A watermark may be clipped by the printable area if it is printed
    across the printable margins. The Watermark Preview Window does not
    reflect the printable area of the selected paper size.



5. General Comments
===================

(1) It is recommended that you restart the Windows system after completion
    of driver installation in order for the driver to work properly.


(2) It is also strongly recommended that you restart the Windows system 
    after completion of driver uninstallation.
    This is to ensure a completely clean system especially if you are
    to perform re-installation of driver. 


(3) If you encounter problem in setting up the driver by SETUP.EXE, you may
    use the Windows Add Printer Wizard to install the driver.
    Please refer to above 3.1, 3.2 and 3.3 sections for guidelines of driver
    installation via the Windows Add Printer Wizard.


(4) After installing the Windows NT4.0/2000/XP FX Document Centre 285/235 PCL 6
    printer driver, you may also install an alternate Windows 95/98 
    printer driver on the Windows NT4.0/2000/XP system by running the SETUP.EXE 
    provided by the Windows 95/98 FX Document Centre 285/235 PCL 6 printer
    driver. 
    This will allow users on the Windows 95/98 system to download it 
    automatically when they connect.


(5) Some applications provide printing options pertaining to the number
    of copies and collating copies.  Always select the printing options
    in the application unless the instructions specify otherwise.
    Use the printer driver dialogs to select advanced options such as
    duplex (2-sided) printing, or options that are not available in the
    application.


(6) Always close the printer driver dialogs and/or the application Print
    dialog before you make any changes to the default settings of the
    printer driver via the Control Panel.


(7) Not all graphics and images can be printed using the "Vector" graphics
    setting. If you use the "Vector" setting and your graphic images do
    not print the same way they appear on your screen, select the "Raster"
    graphics setting and reprint your graphic.


(8) If you expect the printed texts to be "what you see is what you get",
    deselect the "Use Printer's TrueType Fonts" option.


(9) Select and deselect the "Use Printer's TrueType Fonts" option in driver
    will affect the layout of your print job.
    Use of Printer's TrueType Fonts will result in smaller size in texts,
    tables and graphic images printed.
    Do not select "Use Printer's TrueType Fonts" option if you are expecting
    images from the application are printed in their actual sizes.
    It is recommended that you preview the document before printing or sending
    a fax; especially when you change the "Job Type" setting from/to "Fax"
    option with the "Use Printer's TrueType Fonts" option selected.


(10) The driver's Overlay function is enabled for users who are assigned with
     the Administrators / Power Users right.


(11) When using Scaled booklet with document of mixed orientations, the output
     will be printed in Portrait.


(12) Using large percentage for Scale Factor together with large paper size,
     "Scaling" printing may not be possible.

(13) When user specifies a custom paper size within 1.6mm from the standard
     paper size, it's size will be mapped to the nearest standard paper size
     other than Postcard and Folio paper sizes.

(14) When "Pages Per Split" is selected for Booklet Creation, additional blank
     sheets may be printed.

(15) If a user does not specify a job owner name for a print job, the printer
     will use the user's logon name to generate the Print Volume Report.
     However, if a user's logon name contains a double quotation mark (")
     that cannot be recognized by the printer, "Unknown User" will be assumed.

(16) If your Job Offset output does not work well with the collated copies,
     you may try to deselect the "Collate" option in the application
     and check the "Collate" check box in the printer driver.

(17) You can't use the features on Layout tab on the following occasions:
     1. "Job Finishing" on Print tab is off.
        (When sharing the printer driver from a remote machine, you can't use 
	this function.)
     2. You use the driver on Windows Cluster Server.
     3. There isn't "FILE:" port in the priner port.
     On these occasions, the each item on Layout tab is disabled.

(18) If a Fax Phonebook is not initialized or created by the current
    user, he/she may not be granted the authority to access it.
    For such inappropriate access by users, the driver will display
    an error message indicating that the default Fax Phonebook cannot
    be located or the specified Fax Phonebook cannot be recognized.
    On the other hand, if a user would like his/her Fax Phonebook to
    be accessed by other users, he/she has to specify the groups and
    users whose access he/she wants to allow, and must grant them
    at least the 'Change' permission to the Fax Phonebook data file.


6. Limitations
==============

(1) The printed output quality of some pattern-on-colour shaded graphic
    images may not be well handled. You may choose a different graphic
    colour/pattern to resemble the desired printout.


(2)  Colour texts are always printed in Black in most applications when Raster
     mode is selected.
     
     Workaround: Select "Vector" mode to print the job.


(3)  In Vector printing mode, selecting "All Texts to Black" control may not
     apply to some texts that are greater than 70 points. Texts with large
     font size may be printed as graphics and hence its 'black' attribute
     is lost.

     Applications that were tested to have this problem are:
       Microsoft PowerPoint 97
       WordPro 97
    
     Workaround: Select "Raster" mode to print the job.


(4)  Some applications draw graphic images on the page before the text is
     drawn in "Raster" mode. As a result, the graphics may be covered by
     the opaque background of the text and hence, these covered images may
     not be printed physically.
 
     Applications that were tested to have this problem are:
       Microsoft WordPad
       Microsoft Excel 97

     Workaround: Select "Vector" mode to print the job.


(5)  Outline texts must be printed using downloaded fonts.
     "Use Printer's TrueType Fonts" option must be unchecked to print texts as
     outline because device (PCL) fonts do not support Outline attribute.


(6)  The texts in the Data Label of Microsoft Excel 97 may have their font
     background each font printed as white in Raster mode.

     Workaround: Select "Vector" mode to print the job.


(7)  The colour lines in the chart of Microsoft Excel 97 may be printed as
     black in Raster mode.

     Workaround: Select "Vector" mode to print the job.


(8) You may get unexpected stapled position if the Staple function is applied
    to the following print jobs:
    > documents that have page orientation different to that of the driver
      default orientation.
    > N-Up printing of documents that have page size different to that of the
      driver default paper size.


(9) The watermark should not be used for creating an overlay. Otherwise,
    unexpected result may occur.


(10) The driver does not support printing from the Client of the Windows NT4.0
     Terminal Server.


(11) If "Download as Bit Image" is used together with "As Outline Only" for
     the watermarks, the watermarks may not be printed as outline fonts.

     Workaround: Select "Download as TrueType" for the TrueType mode.



7. Known Problems
=================

(1) The N-Up function is not recommended for printing a document that has
    both Portrait and Landscape pages. Depending on the page arrangement of
    a document, the logical page order from one physical page to another
    may be changed.
    For example, if a document has different orientation on its first page
    and third page, the 2-Up printing will output the third and fourth pages
    on the second physical page with swapped order as compared to the first
    and second pages on the first physical page.



8. Software Update
==================
    The latest software is available on our web site.

        http://www.fujixeroxap.com

    Communication charges will be borne by the customer.



Microsoft is the registered trademark of Microsoft Incorporated.
Windows is the registered trademark of Microsoft Incorporated.
Other names of products and companies are the trademarks or
registered trademarks of each company.
Copyright 2001-2003 Fuji Xerox Co., Ltd. All rights reserved.
----------------------------< End of File >-----------------------------------

