( File-Name: GECKOHS2.CNC @ 9/8/07
( HS5084x150mm-GECKO-1D - Heatsink for 2 or 3 x Gecko Controllers
( Spots all individual holes - some to be opened out
( Set start reference datum at x0000 y0000 top left corner
( Install 2.7mm Drill - roll-form tapping drill for M4 thread
( the travel concludes when the cutter reaches x=0.00; y=0.00
( Spindle speed set to 2500rpm
( operation begins automatically when START buttin pressed
( raise the quill at the end of the X-0000 & Y 0000mm stroke
( when appropriate, use a manual command the "X" axis to the
( PITCH distance between each consecitive hole in patch panels etc.
( 80% Kero+ 20% RTD is used as cutting lubricant during the cutting stroke
clr	  	( clear all existing programms/commands
clr	  	( clear all existing programms/commands
p 	  	( programme begin
m 1	  	( set motor to FULL step mode
t 100	  	( set start speed to 100 steps/sec
max 250         ( set MAXimum speed to steps per sec. i.e. 500steps/sec
a 100	  	( set acceleration to 100 steps/sec/sec
de 100          ( set deceleration to 300 steps/sec/sec
k 50		( sets step constant to 50 ?
s 4 1		( check that the TDC switch is closed
<snip>

x 2300                  ( move "X" 15.25mm
y 2650                  ( move "Y" 19.85mm

( make 22.6 diameter hole

o 1 1                   ( send quill DOWN + turn mist ON
s 2 1                   ( depth-reached quill switch opens
o 1 0       ( quill ram - UP
s 4 1                   ( quill switch HOME/closed

x 3500                  ( move "X" 15.25mm
y 0                  ( move "Y" 19.85mm

( make 22.6 diameter hole

x 3500                  ( move "X" 15.25mm
y 0                  ( move "Y" 19.85mm

( make 22.6 diameter hole

x 0000	( move x = 0
y 4852 ( move y = 4952

( make 28.5 diameter hole

x -5300	( move x = -53.00mm
y -799 ( move y = -7.99mm

( make DA15 connector hole 


x 3750          ( move "X" 37.50mm
o 1 1           ( turn mist ON
s 2 10
o 1 0
s 4 1
x 700          ( move "X" 7.00mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x 3050          ( move "X" 30.50mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x 700          ( move "X" 7.00mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x 3750          ( move "X" 37.50mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
y 6030          ( move "Y" 60.30mm
o 1 1
s 2 1
o 1 0
s 4 1
x-3750          ( move "X" 37.50mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x-700          ( move "X" 7.00mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x-3050          ( move "X" 30.50mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x-700
o 1 1
s 2 1
o 1 0
s 4 1
x-3750          ( move "X" 37.50mm
o 1 1           ( turn mist ON
s 2 1
o 1 0
s 4 1
x-1525
y-8015          (return to 0:0 home position
q