( CASA D9-Y+ milling
( drills two holes and mills rectangle-shaped hole in Y direction 
( .
( Install 3 mm cutter
( Set start reference at one mounting hole 
( Spindle speed set to 2500~3000rpm
( 80% Kero+ 20% RTD used as cutting lubricant
( .
clr		( clear all existing programs/commands
p		( begin programme
m 1		( set motor to FULL step mode
t 200		( set start speed to 200 steps/sec
max 400	( set MAXimum motor speed to steps per sec. i.e. 400 steps/sec
a 500		( set acceleration to 500 steps/sec/sec
de 500      ( set deceleration to 1500 steps/sec/sec
k 50        ( sets step constant to 50
( first hole
s 4 0           ( BDC switch OPEN
s 4 1           ( check that the TDC switch is closed
o 1 1           ( mist lubrication on
s 4 0           ( BDC switch OPEN
o 1 0           ( mist lubrication off
y 2499          ( move y to other hole
s 4 1           ( check that the TDC switch is closed
o 1 1
s 4 0           ( BDC switch OPEN
o 1 0
x -390           ( should be 420
y -404           ( should be 374
s 4 1           ( check that the TDC switch is closed
o 1 1
x -30
y 30           ( into the corner
( skew at 10 deg for 8.4 mm
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
( 10
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
( 20
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
( 30
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
( 40
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
y -3
x 17
( 49
y -1
x 7
y -1454
( skew at 10 deg for 8.4 mm
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
( 10 
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
( 20
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
( 30
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
( 40
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
y -3
x -17
( 49
y -1
x -7
y 1750
s 4 0           ( BDC switch OPEN
o 1 0
x 420
y -2125
c 0             ( turn motor current off
q